Stratasys multi-material 3D printing used to support the successful transplantation of a larger-than-average adult kidney from Brendan Clark, into his two-year-old son, Dexter
3D models of patients’ anatomies determined the feasibility of the transplant
Dexter has since made a full recovery and is now able to eat without a feeding tube for the first time since birth
MINNEAPOLIS & REHOVOT, Israel — (BUSINESS WIRE) — May 17, 2018 — Stratasys (Nasdaq: SSYS), a global leader in additive technology solutions, today announced that surgeons at Guy’s and St Thomas’ NHS Foundation Trust, London, are using 3D printing technology to improve the success rates of life-saving, complex organ transplantation in young children. This is exemplified in the case of two-year-old Dexter Clark, who recently received a larger-than-average kidney from his father, Brendan Clark. 3D printing played an important role in the operation, according to Mr. Pankaj Chandak, Transplant Registrar at Guy’s and St Thomas’ NHS Foundation Trust.
This press release features multimedia. View the full release here: https://www.businesswire.com/news/home/20180517005095/en/
Stratasys' multi-material 3D printing supported the successful transplantation of a larger-than-average adult kidney from Brendan Clark, into his two-year-old son, Dexter, by using a 3D printed models of Dexter's abdomen and his father's kidney (Photo: Business Wire).
Guy’s and St Thomas’ NHS Foundation Trust is one of the largest NHS trusts in the U.K., treating more than 2.4 million patients in acute and specialist hospital services and community services every year. Surgeons across the Trust are using Stratasys multi-material 3D printing for planning the most intricate of operations, with the transplant department a pioneer in the use of the technology. Most notably, it is the first Trust in the world to use 3D printed models to pre-plan the successful transplantation of an adult kidney into a small child with anatomical complexities.
In the case of Dexter, it was clear that he would require a kidney transplant before he was even born, with his father as the likely donor. Due to the complications of his illness, Dexter was able to eat only through a feeding tube and unable to enjoy a simple meal time with his parents and three brothers. In order to perform the required transplant, this case presented two distinct challenges for the surgical team. Firstly, Dexter weighed less than 10 kg, significantly increasing the risk. Secondly, his father’s kidney was much larger than that of the average adult male – raising questions as to the potential feasibility and safety of implanting the donor kidney into Dexter’s abdomen.
Typically, conventional medical imaging is used in the pre-surgical planning process for surgeries such as this one, however these often have limitations. As such, the surgeons used a precision, multi-material Stratasys 3D printer, purchased from U.K. Partner, Tri Tech 3D, to produce two intricate, patient-specific models for pre-surgical preparations.
“Using our 3D printer, we worked in collaboration with Nick Byrne and his team – clinical scientists from our medical physics department who specialize in medical imaging. They converted patient CT scans into anatomically accurate, multi-material 3D models. These helped us appreciate aspects such as depth perception and space within the baby’s abdomen, which can often be difficult to ascertain when looking at conventional imaging,” explains Mr. Chandak. “The ability to print a 3D model of the patient’s anatomy in varying textures, with the intricacies of the blood vessels clearly visible within it, enables us to differentiate critical anatomical relations between structures. The flexible materials also allowed us to better mimic the flexibility of organs within the abdomen for simulation of the surgical environment.”
Ordinarily, to reach a decision whether such complex transplants in children are viable, patients such as Dexter would normally have been placed under anaesthesia and the surgeon in some cases required to conduct an invasive surgical exploration to determine feasibility. With 3D printed models of the patient, the need for surgical exploration can be reduced, as the team can safely determine the optimal surgical approach in the pre-planning stages before the patient is on the operating table.
In Dexter’s case, the 3D printed models were also taken into the operating theatre on the day of the transplant and reviewed by Mr. Nicos Kessaris (Consultant Transplant Surgeon at Guy’s and St Thomas’ NHS Foundation Trust). Mr. Kessaris was able to use the models during the operation to assess the best way in which the donor kidney would lie and fit into Dexter’s abdomen.
“This technology has the potential to really enhance and aid our decision-making process both during pre-surgical planning and in the operating room, and therefore can help in the safety of what is a very complex operation and improve our patient care,” says Mr. Chandak.
Emily Clark, Dexter’s mother, comments, “Since the transplant, Dexter is a changed boy, eating solid food for the very first time. We always knew the operation would be complicated but knowing that the surgeons had planned the surgery with 3D models that matched the exact anatomy of my husband’s kidney and son’s abdomen, was extremely reassuring. We hope that Dexter’s case will offer other suffering families similar reassurance that cutting-edge technology, such as 3D printing, can help surgeons better treat their loved ones.”
Michael Gaisford, Stratasys’ Director of Marketing for Stratasys Healthcare Solutions, concludes: “Guy’s and St Thomas’ NHS Foundation Trust is pushing the boundaries of what can be achieved with multi-material 3D printing within healthcare. It is a clear demonstration of the ability for 3D printing to enable physicians to better plan, practice and determine the optimal surgical approach. We are delighted to see Dexter has fully recovered and hope many other children can benefit from such forward-thinking applications of our technology.”
Stratasys is a global leader in additive technology solutions for industries including Aerospace, Automotive, Healthcare, Consumer Products and Education. For nearly 30 years, a deep and ongoing focus on customers’ business requirements has fueled purposeful innovations — 1,200 granted and pending additive technology patents to date — that create new value across product lifecycle processes, from design prototypes to manufacturing tools and final production parts. The Stratasys 3D printing ecosystem of solutions and expertise — advanced materials; software with voxel level control; precise, repeatable and reliable FDM and PolyJet 3D printers; application-based expert services; on-demand parts and industry-defining partnerships — works to ensure seamless integration into each customer’s evolving workflow. Fulfilling the real-world potential of additive, Stratasys delivers breakthrough industry-specific applications that accelerate business processes, optimize value chains and drive business performance improvements for thousands of future-ready leaders. Corporate headquarters: Minneapolis, Minnesota and Rehovot, Israel. Online at: www.stratasys.com, http://blog.stratasys.com and LinkedIn.
Stratasys is a registered trademark and the Stratasys signet is a trademark of Stratasys Ltd. and/or its subsidiaries or affiliates. All other trademarks are the property of their respective owners.
Attention Editors, if you publish reader-contact information, please use:
- USA 1-877-489-9449
- Europe/Middle East/Africa +49-7229-7772-0
- Asia Pacific +852 3944-8888
Stratasys Media Contacts
Stratasys Corporate & North America
+1 518 424 2497
+1 952 906 2726
Europe, Middle East, and Africa
Jonathan Wake / Miguel Afonso, Incus Media
+44 1737 215200
Greater China, Southeast Asia, ANZ, and India
Japan and Korea
+81 3 5542 0042
Mexico, Central America, Caribe and South America
+52 55 4169 4181
+55 (11) 3129 5158