New ASPRS Positional Accuracy Standards for Digital Geospatial Data Released

BETHESDA, Md., March 2, 2015 – The American Society for Photogrammetry and Remote Sensing (ASPRS) is pleased to announce the release of the new Positional Accuracy Standards for Digital Geospatial Data. The new standards are available at: Readers can navigate to the ASPRS Positional Accuracy Standards for Digital Geospatial Data.

The new ASPRS accuracy standards fill a critical need for map users and map makers alike. For centuries, map scale and contour interval have been used as an indication of map accuracy. Users want to know how accurately they can measure different things on a map, and map makers

want to know how accurate maps need to be in order to satisfy user requirements. Those contracting for new maps depend on some form of map accuracy standard to evaluate the tradeoff between the accuracy required vs. how much time and expense are justified in achieving it, and then to describe the accuracy of the result in a uniform way that is reliable, defensible, and repeatable.

The new ASPRS standards address recent innovations in digital imaging and non-imaging sensors, airborne GPS, inertial measurement units (IMU) and aerial triangulation (AT) technologies. Unlike prior standards, the new standards are independent of scale and contour interval, they address higher levels of accuracies achievable by the latest technologies (e.g. unmanned aerial systems and lidar mobile mapping systems), and they provide enough flexibility to be applicable to future technologies as they are developed. Finally, the new standards provide cross references to older standards, as well as detailed guidance for a wide range of potential applications.

No prior U.S. accuracy standard comprehensively addresses the current state of mapping technology, which is why the new ASPRS standards were developed. The National Map Accuracy Standards (NMAS), developed in 1947, are still used because they are simple, but there is no scientific correlation between those standards and current mapping methodologies. The ASPRS 1990 Standards were an improvement over NMAS; however, they did not do well in representing the capabilities of Lidar, orthoimagery, digital mapping cameras or other current technologies in wide-spread use today. The National Standard for Spatial Data Accuracy (NSSDA) is a reporting standard that references the old ASPRS 1990 standards and is cross-referenced in the new ASPRS standards.  NSSDA provides no accuracy thresholds and does not by itself provide any new or updated guidance on how to select or specify an appropriate accuracy for intended applications.

The new ASPRS standards were developed by the ASPRS Map Accuracy Standards Working Group, a joint committee under the Photogrammetric Applications Division, Primary Data Acquisition Division and Lidar Division, which was formed for the purpose of reviewing and updating ASPRS map accuracy standards to reflect current technologies. A subcommittee of this group, consisting of Dr. Qassim Abdullah, Dr. David Maune, Doug Smith, and Hans Karl Heidemann, was responsible for drafting the document. Draft versions of the standard underwent extensive review, both within ASPRS as well as through public review by other key geospatial mapping organizations, prior to final approval by the ASPRS Board of Directors on November 17, 2014.

Founded in 1934, ASPRS is an international professional organization of geospatial information professionals. ASPRS is devoted to advancing knowledge and improving understanding of the mapping sciences to promote responsible application of photogrammetry, remote sensing, geographic information systems and supporting technologies.

Heather Staverman
ASPRS Assistant Director of Communications
301-493-0290 ext.106
Email Contact

Review Article Be the first to review this article

Featured Video
GIS ANALYST I.8030200 for Dallas County at DALLAS, Texas
Structural Engineer for Kiewit at Lenexa, Kansas
Design Engineer (Engineer 1/2) for Los Alamos National Laboratory at Los Alamos,, New Mexico
Architect for Hutton at Wichita, Afghanistan
Structural Engineer 2 (Engineer 2) for Los Alamos National Laboratory at Los Alamos,, New Mexico
3D Designer and Developer for Los Alamos National Laboratory at Los Alamos,, New Mexico
Upcoming Events
IEC 61850 Global 2020 at Brussels Belgium - Oct 26 - 30, 2020
ACM SIGSPATIAL 2020 at Seattle WA - Nov 3 - 6, 2020
Health GIS: STAR (Spatial Thinking in Applied Research) at Online event Calgary Alberta Canada - Nov 18, 2020

© 2020 Internet Business Systems, Inc.
670 Aberdeen Way, Milpitas, CA 95035
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation TechJobsCafe - Technical Jobs and Resumes  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise